DIY BATTERY SYSTEMS FOR CAMPING

Single 12 volt lamp can easily be the largest total draw because several can be running at once and they can be on for hours, especially if camping in the winter when sunlight is lost early. They can amount to a significant load because, if used at all, they are on ALL of the time. A refrigerator usually won’t even work from a battery except to run the igniter when it is running from propane. These do draw significant power and can flatten a very large RV battery in a jiffy. If the trailer batteries run down due to overuse, they must be recharged from the tow vehicle or the lights, pump and refrigerator igniter and other necessary goodies stop working. Recharging the trailer batteries from the regular trailer umbilical can take hours. This is ok if you are traveling anyway, but once you’ve reached your destination, your tow and trailer will seldom be connected. Even connecting the tow directly to the trailer battery with a set of jumper cables to get a higher charge rate means that the tow has to sit and idle for an hour or more to get another couple of days worth of juice into the domestic batteries. I have two domestic batteries for the trailer.

Electrical Testing

But we were novice RV owners and had to learn some lessons the hard way. The first six years we traveled like many other RVers, forced to hop from one campground to the next and one electric plug to the next. Our attempts at dry camping and living off our house battery were not very successful.

How to Check Your RV Electrical System. By Michele Boyer. Updated 11/01/ Share Pin Email If stored in hot weather, the heat can speed up the breakdown of coatings and connections. RV Electrical Systems in General. Line voltage: Purchase and use a line voltage meter or voltage gauge and a polarity tester. These are inexpensive and.

The generator features two modes: An additional 12 V DC output allows for chaining to other units, which can supply your home with a significant amount of wattage. The L weighs just 36 lbs, and comes with a removable strap for easy transport when needed. The included watt solar panel folds up for easy storage when not in use, and comes with its own 30A Anderson ft solar panel extension cord, allowing you to obtain sun far away from where the unit is set up. Reliable Home Backup Power The L has been carefully designed and refined over time to provide a reliable source of energy in the event of a blackout or power failure.

And it’s light enough to take it with you anywhere. Summary If you’re looking for a versatile, lightweight generator that offers a lot of wattage, the L is perfect for your needs. Features The unit comes in a small 14 x 12 x 13 inches size, but provides a big watts of power. The included solar panels are fairly weak, providing just 50 watts each.

How to Hook Up Sunpro Volt Gauges

I’ve been looking forward to a stopover here in West Palm Beach, but the temperature has been in the forties since we arrived, and we only ventured ashore once, for dinner last night. Friday night found us anchored just upstream of the St. Lucie Lock and Dam map , across from the very familiar Corps of Engineers campground and docks.

The docks are inexpensive and include power, but Vector exceeds the length limit.

Hook Up Jo’s in Freer Texas is a campground or RV park that provides sewer connections at some or all of the campsites. Sewer hookups allow you to drain your gray and black water tanks. If you need a campsite with sewer hookups this campground or RV park offers them.

March 17th, Hi, Tom. You could have something else running that will draw the batteries, however I suspect your batteries are not operating at maximum capacity due to sulfation? Lead acid batteries must be charge each month with a multi-stage charge that boils the acid with a high voltage charge during the bulk stage charge to break up the sulphur and then into a float and equalizing stage. Most converters do not have this capability unless you have a very expensive watt inverter or take the batteries out and use a professional multi-stage charger!

Just leaving it plugged in does nothing more than topping them off and letting sulphur collect on the plates and limit the amount of energy storage. A sulfated batter will show a full I would suggest getting the Battery Minder from Northern Tool which will send high impact waves to your battery and break up the sulfation and condition the battery. To check for any other drains on the battery, disconnect the refrigerator by pulling the volt fuse and then take a multimeter set to DC voltage, disconnect the negative post of the house battery, place one probe on the terminal, the other on the empty battery post.

If you see a reading, you have something that is drawing power.

Car Camping Experience at Ontario Parks

Aug 11th, By Mike Sokol Category: What follows is 3 in a part series about basic electricity for RV users and how to protect yourself and your family from shocks and possible electrocution. This series of articles is provided as a helpful educational assist in your RV travels, and is not intended to have you circumvent an electrician.

Two significant problems occur when you hook up your RV using a long or skinny (or both) extension cord. The first is that this “electrical friction” causing the voltage drop makes the wire itself heat up.

Sep 12th, By Mike Sokol Category: What follows is 6 in a part series about basic electricity for RV users and how to protect yourself and your family from shocks and possible electrocution. This series of articles is provided as a helpful educational assist in your RV travels, and is not intended to have you circumvent an electrician.

The author and the HOW-TO Sound Workshops will not be held liable or responsible for any injury resulting from reader error or misuse of the information contained in these articles. If you feel you have a dangerous electrical condition in your RV or at a campground, make sure to contact a qualified, licensed electrician. The bottom pipe, which is hooked to the PSI output of the pump, will have PSI all along its length, while the top pipe, which drains back into the pump, will have 0 PSI along its entire length.

The pressure within each pipe will be equal throughout its length. This is exactly what happens to an electrical outlet in your home or RV. The pressure of the water will cause a current to flow through that small turbine to power your blender making a frozen drink of your choice. In this case we have really big pipes carrying the water to the little turbine, so the small amount of flow current required only causes a 1 PSI drop in pressure in each pipe.

# Car Battery Voltage Drops While Driving #

Polk Somebody recently asked me what I enjoyed the most about RVing. It didn’t take long for me to respond that it was the people you meet at the campground. I don’t know of anywhere else that you can meet complete strangers and within a couple of hours feel as if you’ve known them forever. People at campgrounds are some of the friendliest most helpful people you will ever meet. I have seen it time and again when a camper pulls in and they are having problems with something and their next door neighbor, whom they never met, is right there to assist them.

I have also observed and assisted several campers who were new to RVing and not really sure how to set their unit up when they arrive at the campground.

Unlike the other Belden Hypalon Hook-Up Wires, Belden’s High-Voltage Hypalon Hook-Up Wire does not follow a UL or CSA standard, but it offers a significantly higher voltage rating at volts. This High-Voltage Hook-Up Wire is built with a separator to facilitate stripping.

This will be a nominal V, single phase, 50Hz supply, which is compatible with UK and modern European caravans, motorhomes, trailer tents, folding campers and tent hook-up connections. This electrical supply can be used either directly to power V equipment or indirectly via a power supply unit that converts the mains power at V AC to a nominal 12V DC, usually in conjunction with a leisure battery. This Data Sheet looks at how to use this electricity supply safely and discusses its limitations.

Because your unit is mobile there is a greater likelihood of things going wrong with an electrical installation than with the fixed installation within your house. It is therefore important you make sure your cables and equipment are maintained in good condition by simple checks every time you use it, by regular inspections by a qualified technician and also by using it in a sensible way. Campsite owners and management team in the case of the Club, the Club and its Holiday Site Managers are responsible for the safety of the electrical supply equipment up to the socket outlet on the site bollard where you connect your hook-up cable.

Supply bollard A typical supply bollard A pitch with electrical hook-up will have an electrical supply bollard within about 20 metres. Each Club hook-up bollard is individually protected against overload by a miniature circuit breaker MCB and a residual current device RCD. The MCB is a device to protect the site cabling from overloading and limits the amount of current you can draw from the supply. Hook-ups on Club sites have maximum ratings of 10A or 16A and this will limit the number of appliances you can use at one time see the How much power section.

Installing RV electric hook up in a van : vandwellers

Print Email We’re now nearly three months into our third trip and one of the recurring problems from the previous tours is the matter of drying hair. Sophie, who has lovely long blonde hair, hates not being able to blow dry it properly. We tried all manor of 12v hair dryers which varied from pathetic to down right dangerous with melting wires and popping fuses.

In the end she settled to dry it using the hot air vents in the cab, which in Summer was a bit overpowering! There are two types of inverter, pure sine and modified sine wave. Pure sine wave is the better type which is exactly the same as the electricity you have at home.

Submission 1: Stan (WA4DYD) & Carolyn Edwards. Earlier I have posted links to photos of the replacement of the internal TV antenna with one of the Winegard antennas as a DIY project, an adapter for a 50A RV receptacle to handle two 30A units, reverse engineered the TrippLite remote for the charger-inverter, and documented the installation of my amateur radio installation and CB in our P.

If you’d like to see larger and additional mod images, just click on over to the RV mods picture page. There just is no comparing the 2 antennas, the Jack outperforms the bat wing by a huge margin. You can see the write-up we did when we installed it. Porcelain Toilet We removed the plastic Thetford toilet because it was too low, plastic and cheaply made. We installed a new Dometic Sealand toilet that is taller, porcelain, foot flush and has a residential size seat. It can pull air in, blow air out and act like a ceiling fan.

It is very quiet and moves a ton of air. It can even operate when it is raining. If you need ventilation in your RV, get one of these! Read the MaxxFan review. It is great for keeping an eye on our enclosed trailer while traveling down the road as well as for backing up. You can get you one by clicking here. Installation is ssuper easy and takes very little time. Anything to prevent a leak is worth it to us!

Camping with an Electric Blanket

Side view of a Sundance travel trailer Isuzu ELF 6th gen, standard-cab-type auto-sleeper style recreational vehicle R Pilote recreational vehicle Articulation point The point where two vehicles are coupled together to allow movement, usually by a ball or fifth wheel hitch. Awning On most newer RVs, the manufacturer includes a roll-out awning. The awning can be either manually operated or it can be operated electrically. Another type of awning used by RVers is a portable pop-up canopy or tent that provides a temporary solution to people who want to be outdoors and enjoy shade.

Learn about RV camping, RV travel, RV news and much more. This newsletter, now in its 17th year of continuous publication, is funded primarily through advertising and voluntary subscription contributions from our readers. Thank you! Issue • Week of March 3–9, #rvtravel Receive an email alert for each new issue of this newsletter.

Customer Gallery Johnnys van comes in from the cold – Saturday, January 13th, Oh my we have a whopper of a project here, from the very top to the bottom transformation at the Shak, we will have our design heads on working with Johnny and his wife who are architects and artists. Creative juices will be flowing aright when we meet up next week for our design consultation, where we will discuss everything from the crafted bellows, door cards, upholstery, lighting, electrics, furniture, substrates and materials.

Once agreed we will then work hard to bring it all to fruition, the greatest journey starts with the smallest step. From the top down its roof off, new set of crafted bellows, headlining throughout, led lighting panels, doorcards, new flooring, cab upholstery, full suit of our ultra lightweight hand crafted furniture, with contrasting worktops. New suite of RnR bed cushions on our sturdy metal framed bed, and new cab upholstery up front to match, new ice, check out our Facebook page for progress.

Peabody for phase II of his project.. We have some careful measuring ahead as we work our way through this creative list. Starting from the top fitting of new bellows, hand crafted headlining, led lighting panels, new suite of crafted doorcards, new flooring etc.

RV Technical Tips

In the automotive context, a voltmeter gauge displays the number of volts stored by the vehicle’s battery. Many vehicles, particularly older cars, are equipped with only a dashboard light that illuminates when the battery voltage falls below a normal level. Sunpro manufactures volt gauges that instead feature a needle that moves across a numbered dial to indicate exactly how much voltage the battery has.

Although Sunpro produces a number of volt meters that look different, the process of hooking up the gauge is the same regardless of the external appearance. This wire will serve as the ground wire. A common mounting location is against the interior-side of the firewall or within the engine compartment.

If the campground has a cable TV hook up connect your TV coax cable from the RV to the cable connection. If they don’t offer cable raise the TV antenna on .

For years they have slowly replaced bulbs in many applications like digital displays and the like. Within the past few years “super bright” LEDs as compared to LEDs that have been around for years have come to the market and are now starting to replace lights that need to be bright. Traffic signals and auto taillights are two examples. The advantages of LEDs is their long life and low voltage draw. So, let me think about this, long life and low power usage Sounds like something I want to use when I am dry camping.

Anything that will extend the battery in the pop up is great for me. The first product I have purchased were replacement bulbs for my overhead lights.

How to Repair a Camper Travel Trailer Electrical System

All photos are thumbnails, click to see an enlarged version Power to your camper will be provided via a power distribution box located at your campsite. In this photo we see two breakers in the upper left, one 30 amp which controls the round “RV Style” socket below the breakers, and a 20 amp breaker which controls the “duplex” receptacle to the right.

Remember this is what feeds the electric to most popups so verify that you pop up has working GFIs on all electric circuits. In this photo we see three breakers in the upper left, one 30 amp which controls the round 30a “RV Style” socket below the breakers, one 20 amp breaker which controls the “duplex” v receptacle to the right as well as a 50a dual pole breaker for the 50a RV socket.

Camping with an Electric Blanket. only brand of heated blanket or mattress pad sold in the United States that will work with an MSW inverter is the low voltage SoftHeat one. It could easily become bunched up and overheat – possibly catching fire. Search.

Getting a light shock by touching the siding of your camper is a serious concern and can lead to larger potential problems. If this does occur on your camper, one thing I can say for sure is your camper is not properly grounded to earth ground and recommend it be addressed quickly. Not knowing exactly how Sunline accomplished grounding an entire camper with metal siding to make it safe where ever you touched it, I set out to figure this out.

I have gone out to my own camper and checked on just how did they do this. And now seeing this and the reports here of folks on the forum getting shocked, I can see I myself will add one more annual check to the spring camper startup list. Ensure there is a proper earth ground on the camper siding. Before doing this investigation I never gave that much thought about it. I have tried 3 times now to try and keep this short and sweet but the more I come back to, well everyone may not be an electrical type and at least understanding this may help them prevent a serious injury.

Once understood they may be able to check for themselves or have someone do it for them. So find 5 minutes and read on. First Lets talk about the wording Earth ground, grounding and the word ground what that all means and why it is so important when we plug our campers into the VAC power post. I will try and break this down into simple camper language so everyone can follow along.

The Split Charge Leisure Battery System In Our VW T4